Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Corrosion Resistant Materials Compared: FRP, Steel, Aluminum and Concrete

Glass fiber reinforced plastic (GFRP) is a composite of glass fibers set in a polyester, vinyl ester or epoxy resin matrix, built to carry structural loads without rusting, conducting electricity or absorbing water the way steel, aluminum and concrete do.

Key takeaways:

  • GFRP runs 1.7-2.0 g/cm³, versus 7.85 g/cm³ for structural steel, 2.7 g/cm³ for 6061-T6 aluminum and 2.24-2.40 g/cm³ for normal-strength concrete, per EngineeringToolbox’s materials data.

  • Steel corrodes at 1.3-25 µm/year in rural air and over 200 µm/year in severe industrial or marine air, according to the American Galvanizers Association; GFRP resin resists that chemistry outright rather than relying on a coating.

  • Aluminum resists general corrosion with its oxide layer but is prone to pitting and galvanic attack in chlorides and acids; one cost analysis puts its annual corrosion-related expense at 15-30% of an equivalent steel structure.

  • Concrete’s compressive strength (20-40 MPa) is solid, but its tensile strength is only 2-5 MPa, and sulfuric acid from hydrogen sulfide gas degrades unprotected concrete in wastewater and sewer settings.

  • Over a full lifecycle, GFRP’s higher material cost is usually offset by lower installation and maintenance spend.

What Corrosion Resistant Materials Are Used in Industrial Settings

Four materials dominate corrosion-prone industrial construction: glass fiber reinforced plastic, steel (bare, galvanized or coated), aluminum, and concrete (plain, precast or polymer-modified). Each resists corrosion through a different mechanism, and that mechanism is what determines how it ages.

Fiberglass reinforced plastic, structural FRP and GFRP all describe the same category: continuous or chopped glass fibers embedded in a thermoset resin. The full meaning of GRP is Glass Reinforced Plastic (or Glass Reinforced Polymer); it’s the term used in Europe and Asia for the identical material North America calls FRP. As DEFI’s own FRP vs. GRP guide puts it, GRP is a type of FRP that specifically uses glass fiber, while FRP also covers carbon, basalt and aramid fiber composites. A glass composite material, in engineering terms, is any product where glass fiber reinforcement is bonded to a polymer matrix so the fiber carries tensile load and the resin transfers that load between fibers and protects them from moisture and chemicals.

Manufacturers turn fiber-reinforced plastic resin and fiber into finished shapes through several processes: pultrusion, resin transfer molding, compression molding and hand lay-up, each suited to different shapes and production volumes. Pultrusion continuously pulls fiber rovings through a resin bath and a heated die to produce structural shapes, such as beams, channels and grating, with consistent properties end to end. Resin transfer molding instead injects resin into a closed mold to produce smaller, high-precision parts, and compression molding presses a preheated resin charge into shape under a top plug. GRP composites, CFRP (carbon fiber), BFRP (basalt fiber) and AFRP (aramid fiber) all belong to the same reinforced-plastic FRP family and are processed by these same methods; glass remains the most widely manufactured fiber because it balances strength, cost and corrosion resistance better than the alternatives for most industrial grating and structural products.

Steel resists corrosion only when it’s protected, by galvanizing, paint, or cathodic protection. Aluminum self-passivates with a thin oxide film. Concrete relies on its alkalinity and a protective cover over any embedded steel reinforcement. GFRP is different: the resin itself, not a surface treatment, is what resists the chemical attack, which is why DEFI’s grating and structural shapes don’t need recoating on a schedule the way steel and concrete do, per its FRP vs. steel comparison.

FRP vs Steel: Strength, Weight and Maintenance

FRP structural profiles match steel on tensile strength at roughly a quarter of the weight, but steel still leads on stiffness, which is why the two materials get sized differently rather than swapped one for one. Table 1 lines up the core mechanical properties engineers check first.

Property

Pultruded FRP (lengthwise)

Structural Steel (A-36)

Density

1.7-2.0 g/cm³

7.85 g/cm³

Tensile strength

30,000 psi

~60,000 psi

Compressive strength

30,000 psi

36,000 psi (yield)

Modulus of elasticity

2.5-2.8 million psi

29 million psi

Electrical conductivity

Non-conductive (~200 V/mil dielectric)

Conductive

Source: DEFI’s structural profile testing data, reported against ASTM coupon test methods.

That lower modulus of elasticity is the real trade-off: FRP deflects more than steel under the same load, so engineers typically spec a deeper or thicker section rather than a direct swap. Once sized correctly, though, FRP wins on weight and corrosion. A comparable fiberglass I-beam runs about 11 pounds per foot against roughly 44 pounds per foot for its steel equivalent, which is why FRP installs with hand tools while steel generally needs a crane, rigging crew and reinforced foundation.

Maintenance is where the gap compounds. Bare carbon steel in a severe industrial or marine atmosphere loses more than 200 µm of section thickness per year, and even a properly galvanized coating typically needs full repainting or re-galvanizing every 10 to 25 years in aggressive service, per the American Galvanizers Association. FRP doesn’t carry that recoating cycle because corrosion resistance comes from the resin matrix all the way through the part, not a surface layer.

FRP vs Aluminum: Corrosion and Cost Over Time

Aluminum resists general corrosion with a self-forming oxide layer, but that layer breaks down under chlorides and acids, and aluminum conducts electricity, two gaps FRP doesn’t share.

6061-T6 aluminum, a common structural grade, runs 2.7 g/cm³ with a tensile strength around 270 MPa (39,000 psi) and a modulus of 69 GPa, per EngineeringToolbox’s alloy data. That makes it lighter than steel and reasonably strong, which is why it shows up in some of the same platforms, cages and enclosures FRP competes for. The oxide film that protects it, though, is vulnerable to pitting in chloride-rich environments and to galvanic corrosion when aluminum is fastened to a dissimilar metal, a mechanism documented across multiple aluminum-alloy corrosion studies. One industry cost analysis estimates aluminum’s annual corrosion-related expense at 15-30% of an equivalent carbon steel structure, lower than steel, but not zero.

FRP’s resin doesn’t form a galvanic cell with anything, because it isn’t a metal. There’s no dissimilar-metal pairing to manage, and no passivation layer that can be breached by a chloride pit. On the electrical side, aluminum conducts, so it still needs grounding and bonding around live equipment; FRP’s dielectric strength of roughly 200 volts/mil makes it the default choice instead of aluminum near substations, transformer platforms and other electrically sensitive sites, a distinction covered in DEFI’s difference between FRP and GRP overview of the material’s non-conductive properties. For data centers and petrochemical sites weighing non-conductive options, that single property often decides the comparison before cost even enters it.

FRP vs Concrete: Installation and Long Term Durability

Concrete carries compressive loads well but corrodes chemically under acid and sulfate attack, and once embedded steel reinforcement starts rusting, the damage accelerates from the inside out.

Normal-strength Portland cement concrete runs 20-40 MPa (3,000-6,000 psi) in compression but only 2-5 MPa in tension, with a density of 2,240-2,400 kg/m³. That low tensile number is why concrete structures need steel reinforcement for anything beyond pure compression, and that reinforcement is exactly what corrodes when chlorides or acids reach it.

Wastewater and sewer infrastructure is the clearest case study. Hydrogen sulfide gas off-gassing from wastewater converts to sulfuric acid on exposed concrete surfaces, a bio-corrosion mechanism that a 2024 review found costs the sewer industry billions of dollars in maintenance worldwide. At one New Orleans wastewater treatment plant, corrosion degraded grit chamber sidewalls to a depth of 25-40 mm, according to a case study published in the ASCE Journal of Cold Regions Engineering. Unsealed concrete is porous, so water and dissolved chemicals work into it and cause cracking, spalling and chipping over time, a pattern DEFI’s trench drain materials guide lays out alongside FRP’s resin-based alternative.

Installation tells a similar story in reverse. Concrete needs formwork, cure time and heavy equipment to place, and relative installation cost for GFRP runs about half that of steel while GFRP’s own lifecycle maintenance cost sits at roughly 15-25% of steel’s, against concrete’s 60-75%. FRP covers and structural members install with hand tools, on grade or retrofitted into an existing slab, without the cure time or forming that concrete requires.

Where FRP Grating and Structural Profiles Outperform Alternatives

FRP grating and structural profiles outperform steel, aluminum and concrete specifically where corrosion, electrical conductivity or dead weight rule out the alternative, not as a universal replacement for every application.

In water and wastewater treatment, the same sulfuric acid attack that degrades concrete and the chlorides that pit steel and aluminum don’t touch a properly formulated resin; vinyl ester FRP has shown corrosion rates below 0.001 mm per year with service lives past 30 years without recoating, per DEFI’s own materials data. In petrochemical and offshore settings, the same resin resists acids, caustics and salt spray that force steel onto a recoating schedule. In data centers and substations, FRP’s non-conductive, electromagnetically transparent profile replaces aluminum and steel without the grounding and bonding work those metals require.

DEFI builds its FRP grating options with a grit-top anti-skid surface as standard, 316 stainless steel clips and hardware, and fluorescent or bright color finishes that improve visibility in low-light plant environments. Those details matter in the industries that lean on FRP hardest: amusement and water parks dealing with chlorinated pool chemistry, agriculture operations exposed to fertilizers and manure acids, and offshore platforms where weight savings reduce crane time and improve buoyancy margins. For deeper background on the material itself, DEFI’s fiber reinforced plastic resources and more on FRP materials tag pages cover specific applications in more depth.

Choosing the Right Material for Your Facility

The right material depends on which failure mode your facility actually faces, not a general reputation for strength or cost.

  • Choose FRP when the environment includes acids, caustics, salt spray or constant moisture, when electrical conductivity is a safety risk, or when crane access and foundation loading are limited.

  • Choose steel when stiffness-critical, high-load applications justify the weight and a realistic coating or galvanizing maintenance plan is budgeted in from the start.

  • Choose aluminum when weight savings matter but the environment is drier or less chloride-exposed than a coastal or chemical-processing site, and where its conductivity isn’t a liability.

  • Choose concrete for foundations, slabs and high-compression applications, paired with a corrosion-resistant cover or cladding, such as FRP grating, wherever acids or chlorides reach the surface.

Most industrial sites end up using more than one of these materials for different parts of the same structure. The comparison that matters is lifecycle cost for your specific chemical exposure and load case, not which material wins on a single spec sheet number. If your facility is weighing FRP against steel, aluminum or concrete for a specific application, request a free quote and DEFI’s team can size the material to your exposure, load and budget.

FAQ

What is fiberglass reinforced plastic?

Fiberglass reinforced plastic (FRP) is a composite made of glass fibers embedded in a thermoset resin, usually polyester, vinyl ester or epoxy. The fibers provide tensile strength and stiffness, and the resin matrix transfers load between fibers while protecting them from moisture and chemical attack. It’s manufactured into grating, structural shapes, stairs and handrails as a non-conductive, corrosion-resistant alternative to steel, aluminum and wood.

What is the full meaning of GRP?

GRP stands for Glass Reinforced Plastic, also written Glass Reinforced Polymer. It’s the term used across Europe, the UK and much of Asia for the same glass-fiber composite that North American suppliers call FRP, per DEFI’s FRP vs. GRP breakdown. The split is terminology, driven by regional standards bodies, not a difference in the material itself.

What is glass composite material?

A glass composite material is any product in which glass fibers are bonded to a polymer resin matrix so the fibers carry the tensile and flexural load while the resin holds them in position and shields them from the surrounding environment. GFRP, GRP and fiberglass all describe this same category when the reinforcing fiber is glass.

What are the mechanical properties of GFRP?

Pultruded GFRP structural shapes commonly test at around 30,000 psi tensile, flexural and compressive strength lengthwise, with a modulus of elasticity of 2.5-2.8 million psi and a density of 1.7-2.0 g/cm³, per DEFI’s structural profile data. A separate published laminate reference, EN 13706 grade E23, lists a longitudinal tensile strength of 240 MPa and a longitudinal tensile modulus of 23 GPa at a density of 1.9 g/cm³. Exact figures vary by resin system, fiber loading and manufacturer, so always check the specific product’s test data sheet.

Is FRP stronger than steel?

Not on every measure. FRP can match steel’s tensile strength at a fraction of the weight, but steel has a far higher modulus of elasticity, around 29 million psi versus FRP’s 2.5-2.8 million psi, per DEFI’s structural profile testing data, so it resists deflection better at a given section size. Engineers typically spec a deeper or thicker FRP member to match steel’s stiffness rather than substituting an identical-size part.

Does FRP corrode or rust?

No. FRP contains no metal, so it can’t rust, and its resin matrix resists most acids, bases and salts without a coating that can wear through. Vinyl ester FRP has shown corrosion rates below 0.001 mm per year in corrosive service, according to DEFI’s own testing data, compared with steel’s 1.3 µm to over 200 µm of annual section loss depending on the atmosphere.

How much does FRP weigh compared to steel and aluminum?

FRP runs roughly a quarter of the weight of an equivalent steel section and is lighter than 6061-T6 aluminum as well, 1.7-2.0 g/cm³ versus aluminum’s 2.7 g/cm³ and steel’s 7.85 g/cm³. That weight difference is why FRP structural members ship on standard freight and install with hand tools in cases where steel requires cranes and rigging crews.